Terry_Cowan (16K)
Dagger Tools




Other Albums By Douglas Cygan

Browse All Albums

Created By: Douglas Cygan

1938 BMW 327 Album 1 (31)
Sort by Title  Sort by Size
9990179957302.jpg
C8) New rear seat bucket installed
(23.21 KB)

9990179956750.jpg
C3)Rear frame rail
(38.28 KB)

Boxing in the rear frame rails
9980179957216.jpg
C7) Bottom view of chassis
(40.14 KB)

9990179958434.jpg
F) New front cowl pieces with inner metal supports spot-welded in and Trafficator opening cutout
(43.47 KB)

9990179957062.jpg
C5) Almost completed finish work on chassis
(43.60 KB)

9990179958614.jpg
G2) Newly formed lower trunk floor
(47.46 KB)

9990179959085.jpg
H4) Original gas tank
(49.82 KB)

An original gas tank used for patterns
9990179957909.jpg
D4) New Ash wood left side B-post being fitted
(51.05 KB)

9990179958789.jpg
H1) New gas tank showing top with Pittsburg lock seam
(51.36 KB)

9990179958366.jpg
E3) Newly formed left side fenderwell and rear quarter
(52.45 KB)

9990179958144.jpg
E1) New B-post metal being fitted
(52.77 KB)

9990179957139.jpg
C6)Chassis underside
(53.09 KB)

9990179956325.jpg
B1) Left side-mounted on rottisserie
(53.85 KB)

Fenderwell fitting
9990179955956.jpg
A) 1938 BMW 327
(54.11 KB)

My website is: www.dougcygan.com
9990179957390.jpg
D1) New Ash wood left side A-post shown from front
(55.07 KB)

9990179956444.jpg
B2)Right side-mounted on rottisserie
(55.54 KB)

9990179958860.jpg
H2) Newly formed gas tank
(55.69 KB)

9990179959484.jpg
J) New left rear fender being formed
(55.85 KB)

9990179956537.jpg
C1) Chassis
(55.99 KB)

Chassis being repaired and new floor boards,
9990179958234.jpg
E2) New B-post and rear quarter
(58.60 KB)

9990179956644.jpg
C2) Rear frame
(58.62 KB)

Frame rails being boxed as original for added strength
9980179959357.jpg
I3)New rear deck panels viewed from right side
(62.24 KB)

9990179958698.jpg
G3) Pullmax dies used to stamp bulls-eyes
(63.53 KB)

9990179959357.jpg
I2) New rear deck pieces being fabricated and positioned on original deck
(66.03 KB)

9990179956920.jpg
C4) An original fenderwell
(67.03 KB)

This fenderwell and rear chassis section was used for templates
9990179957776.jpg
D2) New Ash wood A-post and dash support being
(68.48 KB)

9990179957479.jpg
D3) New left side A-post shown from back sidea-post left new 2.jpg
(68.75 KB)

9990179958952.jpg
H3) Forming gas tank ends
(71.53 KB)

Gas tank ends being formed in Pullmax
9990179958533.jpg
G1) Original trunk floor adjacent to new one
(72.26 KB)

9990179958010.jpg
D5) 3-D Router Carver
(74.37 KB)

Home made 3-D router carver to form complex wooden pieces
9990179959202.jpg
I1) Rear deck wireframe buck used to form new
(74.89 KB)





This site and its pages are © Metalshapers Association 2005.

All rights to the content presented on this site is retained by its original authors or the Metalshapers Association, and appears here under license. Any use by third parties requires permission from the original author. All rights reserved. Click here for details.
 
Some of the equipment and methods shown on this site can cause SERIOUS INJURY or DEATH if used improperly or with negligence. The display of equipment or methods here does not constitute endorsement or insure suitability for any particular use. The user is entirely responsible for their own actions, and assumes any and all associated risks.


This site is hosted by the Metalshapers Association