Terry_Cowan (16K)




Other Albums By Joel Ludwig

Browse All Albums

Created By: Joel Ludwig


Rigid Chopper (34)
Sort by Title  Sort by Size
9990242345013.jpg
Welding tank mount to tunnel
(90.96 KB)

Welded on back side.
9980242345012.jpg
Trimming for the tank mount and vent tube
(75.01 KB)

Ready to weld
9990232601453.jpg
tank weld 1.jpg
(76.49 KB)

9960242345013.jpg
Tank Vent
(68.89 KB)

Tube installed in tank for vent.
9980242345013.jpg
tank tunnel mount
(124.18 KB)

Hidden tank mount
9990322282671.jpg
tank lf.jpg
(136.00 KB)

Ready for fuel.
9990226990807.jpg
Tank Buck rear view
(100.09 KB)

The stations need sanding to final fit.
9990226990804.jpg
Tank buck profile
(110.46 KB)

Mockup of the tank buck
9990226990805.jpg
Tank Buck
(110.90 KB)

Starting to fit the fuel tank buck
9980232600721.jpg
tank and fender.jpg
(63.39 KB)

Starting assembly of Tank and Rear Fender
9990311231791.jpg
tail light mounted.jpg
(70.17 KB)

9960311231792.jpg
tail light housing 1.jpg
(61.96 KB)

Mounted tail light housing
9960311231791.jpg
tail light 4.jpg
(87.67 KB)

9990226990808.jpg
Rear Fender Buck
(67.36 KB)

Rear fender buck, 1/2" plywood
9980322282670.jpg
r fender.jpg
(145.54 KB)

Painted
9950242345013.jpg
Hidden tank mount
(96.56 KB)

Two bolts hold the tank down.
9980311231791.jpg
head light 1a.jpg
(237.09 KB)

9980226990807.jpg
Fuel Tank Buck Stations
(97.20 KB)

The stations are fitted.
9990226030895.jpg
Frame on jig
(103.41 KB)

Simple frame jig
9990226030896.jpg
Frame Fabrication
(106.64 KB)

Fitting the tubing
9990242345012.jpg
Fitting the tunnel to the tank
(67.47 KB)

Tack welded together.
9970226030895.jpg
First mockup
(97.83 KB)

4" up and 1.5" forward, 35 degrees.
9980242345014.jpg
Fender fit
(108.93 KB)

Trimming the fender
9990322456787.jpg
dsc01944a.jpg
(222.00 KB)

Almost ready to ride.
9970322456787.jpg
dsc01941a.jpg
(195.67 KB)

9990322456786.jpg
dsc01938a.jpg
(196.03 KB)

9990322282670.jpg
Chopper Tank
(145.03 KB)

The tank is ready for installation.
9990232600720.jpg
chopper 5.jpg
(90.35 KB)

First Mockup
9970232600721.jpg
chopper 4.jpg
(156.57 KB)

So far so good.
9960232600721.jpg
chopper 2.jpg
(122.68 KB)

First daylight
9990242345014.jpg
Checking clearance
(140.71 KB)

Mounting the tank and rear fender
9980226030895.jpg
Almost a Roller
(67.13 KB)

Ready for Tank and Fender Fabrication
9990311231792.jpg
06-22-08_1606.jpg
(31.28 KB)

Trimming and fitting tail light shell
9970311231792.jpg
06-22-08_1338.jpg
(26.74 KB)

Outer shell for tail light




This site and its pages are Metalshapers Association 2005.

All rights to the content presented on this site is retained by its original authors or the Metalshapers Association, and appears here under license. Any use by third parties requires permission from the original author. All rights reserved. Click here for details.

Some of the equipment and methods shown on this site can cause SERIOUS INJURY or DEATH if used improperly or with negligence. The display of equipment or methods here does not constitute endorsement or insure suitability for any particular use. The user is entirely responsible for their own actions, and assumes any and all associated risks.


This site is hosted by the Metalshapers Association